Maker Faire Build Night 2015-02-12: Difference between revisions
No edit summary |
No edit summary |
||
| Line 4: | Line 4: | ||
We started with the task of gathering a couple test materials and building our test pieces for the table top. | We started with the task of gathering a couple test materials and building our test pieces for the table top. | ||
[[File:Materials Ready 2015-02-12 .jpg|640px | [[File:Materials Ready 2015-02-12 .jpg|640px]] | ||
TAP Plastics recommended Ultra-Glo resin for this project. Apparently this resin can also be used to finish the wood on the table so we can go right over the resin and wood together to give the final table top a smooth flush surface. The finished table based on the design so far will end up needed about 110 oz of resing to make the Noisebridge logo. | TAP Plastics recommended Ultra-Glo resin for this project. Apparently this resin can also be used to finish the wood on the table so we can go right over the resin and wood together to give the final table top a smooth flush surface. The finished table based on the design so far will end up needed about 110 oz of resing to make the Noisebridge logo. | ||
[[File:Howard routing 2015-02-12 .jpg|640px | [[File:Howard routing 2015-02-12 .jpg|640px|Howard hadn't used a router before but it would be hard to tell, he did a great job.]] | ||
The channels cut into the test piece are approximately the same width as in the final tabletop. This should give us a good idea of how the lighting will look and how to make the design better. | The channels cut into the test piece are approximately the same width as in the final tabletop. This should give us a good idea of how the lighting will look and how to make the design better. | ||
| Line 13: | Line 13: | ||
[[File:Both halves of the test peice 2015-02-12 .jpg|640px | [[File:Both halves of the test peice 2015-02-12 .jpg|640px]] | ||
The current detail of the lighting channel using a sheet of 1/2" wood for the resin logo and then a 3/4" sheet for the LEDs and the substructure for table top. We plan to cut these together, free hand, so that both pieces match. | The current detail of the lighting channel using a sheet of 1/2" wood for the resin logo and then a 3/4" sheet for the LEDs and the substructure for table top. We plan to cut these together, free hand, so that both pieces match. | ||
[[File:Adhering mylar backing 2015-02-12 .jpg|640px | [[File:Adhering mylar backing 2015-02-12 .jpg|640px]] | ||
At TAP Plastics, they said the resin will not stick to mylar sheets. We have used spray adhesive to stick the mylar to the back of the resin test piece. This was then screwed to another piece of plywood to support the resin as it sits on top of the mylar. The mylar will be removed once the resin has cured | At TAP Plastics, they said the resin will not stick to mylar sheets. We have used spray adhesive to stick the mylar to the back of the resin test piece. This was then screwed to another piece of plywood to support the resin as it sits on top of the mylar. The mylar will be removed once the resin has cured | ||
[[File:Mixing resin 2015-02-12 .jpg|640px | [[File:Mixing resin 2015-02-12 .jpg|640px|Two minutes of mixing per batch is surprisingly tiring]] | ||
[[File:Pouring the resin 2015-02-12 .jpg|640px | [[File:Pouring the resin 2015-02-12 .jpg|640px]] | ||
[[File:Finished pour 2015-02-12 .jpg|640px | [[File:Finished pour 2015-02-12 .jpg|640px]] | ||
[[File:Removing the bubbles 2015-02-12 .jpg|640px | [[File:Removing the bubbles 2015-02-12 .jpg|640px]] | ||
Revision as of 19:29, 14 February 2015
This is part of the Noisebridge Booth for Maker Fair 2015 project
The project has begun!
We started with the task of gathering a couple test materials and building our test pieces for the table top.
TAP Plastics recommended Ultra-Glo resin for this project. Apparently this resin can also be used to finish the wood on the table so we can go right over the resin and wood together to give the final table top a smooth flush surface. The finished table based on the design so far will end up needed about 110 oz of resing to make the Noisebridge logo.
The channels cut into the test piece are approximately the same width as in the final tabletop. This should give us a good idea of how the lighting will look and how to make the design better.
The current detail of the lighting channel using a sheet of 1/2" wood for the resin logo and then a 3/4" sheet for the LEDs and the substructure for table top. We plan to cut these together, free hand, so that both pieces match.
At TAP Plastics, they said the resin will not stick to mylar sheets. We have used spray adhesive to stick the mylar to the back of the resin test piece. This was then screwed to another piece of plywood to support the resin as it sits on top of the mylar. The mylar will be removed once the resin has cured
