Akelly at 22:17, 30 May 2018

2018-05-30T22:17:32Z

← Older revision		Revision as of 15:17, 30 May 2018
Line 39:		Line 39:

	We also have two reflow ovens! One of them has aftermarket firmware flashed to it. You can do custom temperature curves!		We also have two reflow ovens! One of them has aftermarket firmware flashed to it. You can do custom temperature curves!

	~~== Hot Air Station ==~~

	~~Generally only used for rework and repair, use the oven for initial assembly~~

Akelly at 22:16, 30 May 2018

2018-05-30T22:16:12Z

← Older revision		Revision as of 15:16, 30 May 2018
Line 5:		Line 5:

	In KiCAD, you export a DXF of the solder paste layer using the File > Plot tool:		In KiCAD, you export a DXF of the solder paste layer using the File > Plot tool:
	[[File:Kicad_Solder_Paste_DXF_Settings.JPG]]
			[[File:Kicad_Solder_Paste_DXF_Settings.JPG\|400px]]

	Import that into RDWorks, then do a kerf compensation to shrink all the pads. [http://www.qualiecocircuits.co.nz/stencil-technology-other-aspects.htm The finer the pitch component, the more kerf compensation you need in order to leave a reasonable amount of material between two adjacent pads.] Adafruit recommends 2 mil.		Import that into RDWorks, then do a kerf compensation to shrink all the pads. [http://www.qualiecocircuits.co.nz/stencil-technology-other-aspects.htm The finer the pitch component, the more kerf compensation you need in order to leave a reasonable amount of material between two adjacent pads.] Adafruit recommends 2 mil.

Akelly: Created page with "Let's assemble boards in volume! == Solder Paste Stencils == The laser cutter can cut Mylar or Kapton sheets into stencils for spreading solder paste onto a board. 4-5 mil th..."

2018-05-30T22:14:51Z

Created page with "Let's assemble boards in volume! == Solder Paste Stencils == The laser cutter can cut Mylar or Kapton sheets into stencils for spreading solder paste onto a board. 4-5 mil th..."

New page

Let's assemble boards in volume!

== Solder Paste Stencils ==
The laser cutter can cut Mylar or Kapton sheets into stencils for spreading solder paste onto a board. 4-5 mil thickness is pretty common, but for really fine pitch parts you want a thinner stencil. [https://learn.adafruit.com/smt-manufacturing/laser-cut-stencils Adafruit says they use 2 mil Kapton] from [https://www.mcmaster.com/#2271K2 McMaster] but [https://www.ebay.com/p/3M-PP2200-Plain-Paper-Copier-Transparency-Film/691282785 Mylar (3M PP2200 4 mil transparency film) is about 100x cheaper], but melts instead of burns, leaving a slightly worse result, and has the potential for the cut pieces to stick back to themselves.

In KiCAD, you export a DXF of the solder paste layer using the File > Plot tool:
[[File:Kicad_Solder_Paste_DXF_Settings.JPG]]

Import that into RDWorks, then do a kerf compensation to shrink all the pads. [http://www.qualiecocircuits.co.nz/stencil-technology-other-aspects.htm The finer the pitch component, the more kerf compensation you need in order to leave a reasonable amount of material between two adjacent pads.] Adafruit recommends 2 mil.

Either cutting or scanning will work. If you use the scan mode like Adafruit or [https://www.youtube.com/watch?v=zyB-01p7AtI Felix Rusu], there is no chad left. [http://www.juanjchong.com/2014/cutting-mylar-solder-stencils-from-expresspcb-and-eaglecad-files/ Juan Chong] uses two sheets of Mylar, and only cuts through the top sheet, so that the chads stick to the bottom sheet.

{| class="wikitable"
! Material
! Thickness
! Cut Style
! Speed (mm/s)
! Scan Interval
! Min Power
! Max Power
|-
| Kapton
| 5 mil
| Scan
| 200
| 0.05mm
| 20
| 20
|}

Once your stencil is cut, line it up on the board, tape it down and use a credit card or flexible metal paint scraper to spread the paste across the stencil. [https://www.sparkfun.com/tutorials/58 Read Sparkfun's tutorial.] If you're doing multiple boards, you can cut the outline of your board in 1/16" acrylic, line up the stencil and then tape the stencil to the acrylic on one side, so that you don't have to line up the stencil every time.

== Pick and Place ==

We have a Liteplacer! Roy was working on installing the software. If you're only making a couple boards, placing the components by hand with tweezers is faster.

== Infrared Reflow Oven ==

We also have two reflow ovens! One of them has aftermarket firmware flashed to it. You can do custom temperature curves!

== Hot Air Station ==

Generally only used for rework and repair, use the oven for initial assembly

Surface Mount Assembly - Revision history

Akelly at 22:17, 30 May 2018

Akelly at 22:16, 30 May 2018

Akelly: Created page with "Let's assemble boards in volume! == Solder Paste Stencils == The laser cutter can cut Mylar or Kapton sheets into stencils for spreading solder paste onto a board. 4-5 mil th..."