Marvin - Revision history

Ⅹ: command reference

2018-01-13T20:24:11Z

command reference

← Older revision		Revision as of 13:24, 13 January 2018
Line 22:		Line 22:

	[[File:Marvin-PCB-Back.jpg\|800px]]		[[File:Marvin-PCB-Back.jpg\|800px]]


			== Commands ==

			=== sys ===

			System commands for general module configuration

			<pre>
			sys sleep MILLIS
			sys reset
			sys eraseFW
			sys factoryRESET

			sys set nvm ADDRESS DATA
			sys set pindig PIN_NAME PIN_STATE
			sys set pinmode PIN_NAME PIN_MODE

			sys get ver
			sys get nvm ADDRESS
			sys get vdd
			sys get hweui
			sys get pindig PIN_NAME
			sys get pinana PIN_NAME
			</pre>

			*PIN_NAME == GPIO0-GPIO13, UART_CTS, UART_RTS, TEST0, TEST1
			*PIN_STATE == 1 or 0
			*PIN_MODE == digout, digin, ana
			**GPIO0-GPIO3 & GPIO5-GPIO13 can be set to analog (ana)
			**Pins default to output mode, driven low


			=== mac ===

			MAC physical network interface layer

			<pre>
			mac reset
			mac tx TYPE PORT_NO DATA
			mac join MODE
			mac save
			mac forceENABLE
			mac pause
			mac resume

			mac set devaddr ADDRESS
			mac set deveui DEV_EUI
			mac set appeui APP_EUI
			mac set nwkskey NETWORK_SESSION_KEY
			mac set appskey APP_SESSION_KEY
			mac set appkey APP_KEY
			mac set pwridx POWER_INDEX
			mac set dr DATA_RATE
			mac set adr ADAPTIVE_DATA_RATE
			mac set bat BATTERY_LEVEL
			mac set retx RETRANSMISSION_NUMBER
			mac set linkchk LINK_CHECK_INTERVAL
			mac set rxdelay1 RX_DELAY
			mac set ar AUTOMATIC_REPLY
			mac set rx2 DATA_RATE FREQUENCY
			mac set sync SYNC_WORD
			mac set upctr UP_LINK_COUNTER
			mac set dnctr DOWN_LINK_COUNTER
			mac set ch drrange CHANNEL_ID MIN_RANGE MAX_RANGE
			mac set ch status CHANNEL_ID STATUS

			mac get devaddr
			mac get deveui
			mac get appeui
			mac get dr
			mac get pwridx
			mac get adr
			mac get retx
			mac get rxdelay1
			mac get rxdelay2
			mac get ar
			mac get rx2
			mac get dcycleps
			mac get mrgn
			mac get gwnb
			mac get status
			mac get sync
			mac get upctr
			mac get dnctr
			mac get ch
			</pre>

			POWER_INDEX == 5, 7, 8, 9, 10


			=== radio ===

			Radio specific control such as frequency and power levels.

			<pre>
			radio rx RX_WINDOW_SIZE
			radio tx DATA
			radio cw CW_STATE

			radio set mod lora
			radio set freq FREQUENCY
			radio set pwr OUTPUT_POWER
			radio set sf SPREADING_FACTOR
			radio set crc CRC_HEADER
			radio set iqi IQ_INVERT
			radio set cr CODING_RATE
			radio set wdt WATCH_DOG_TIMER
			radio set sync SYNC_WORD
			radio set bw BANDWIDTH

			radio get mod
			radio get freq
			radio get pwr
			radio get sf
			radio get crc
			radio get iqi
			radio get cr
			radio get wdt
			radio get sync
			radio get bw
			radio set snr
			</pre>

📻: functional'ish code

2018-01-09T01:37:03Z

functional'ish code

@@ Line 5: / Line 5: @@
 Source code here: https://github.com/iotacademy/marvin
-The device is a bare PCB with a USB on one end. Plugging this in to a computer shows up as a Arduino Leonardo and can be reprogrammed as such from the Arduino IDE. There is also a micro usb connection presumably connected to the lora module in some way.
+The device is a bare PCB with a USB on one end. Plugging this in to a computer shows up as a Arduino Leonardo and can be reprogrammed as such from the Arduino IDE. There is also a micro usb connection presumably duplicating the male PCB connector.
 Note that this version varies from original kickstarter project, it uses the [https://www.microchip.com/wwwproducts/en/RN2903 Microchip RN2903] at 915 Mhz for US.
 Datasheet: http://www.microchip.com/mymicrochip/filehandler.aspx?ddocname=en578921 (available from digikey and others for < $15)
 [[File:Marvin-PCB.jpg|800px]]
 [[File:Marvin-PCB-Back.jpg|800px]]

Ⅹ: gateway link

2018-01-07T06:38:18Z

gateway link

← Older revision		Revision as of 23:38, 6 January 2018
Line 1:		Line 1:
			See also: [[MTCDT]] (Ethernet/LoRa gateway)

	Some kind of LoRa device http://www.rdmmakerspace.nl/Marvin/		Some kind of LoRa device http://www.rdmmakerspace.nl/Marvin/

Ⅹ: RN2903A

2018-01-07T06:37:11Z

RN2903A

← Older revision		Revision as of 23:37, 6 January 2018
Line 5:		Line 5:
	The device is a bare PCB with a USB on one end. Plugging this in to a computer shows up as a Arduino Leonardo and can be reprogrammed as such from the Arduino IDE. There is also a micro usb connection presumably connected to the lora module in some way.		The device is a bare PCB with a USB on one end. Plugging this in to a computer shows up as a Arduino Leonardo and can be reprogrammed as such from the Arduino IDE. There is also a micro usb connection presumably connected to the lora module in some way.

	[[File:Marvin-PCB.jpg\|~~600px~~]]		Note that this version varies from original kickstarter project, it uses the [https://www.microchip.com/wwwproducts/en/RN2903 Microchip RN2903] at 915 Mhz for US.

			Datasheet: http://www.microchip.com/mymicrochip/filehandler.aspx?ddocname=en578921 (available from digikey and others for < $15)

			[[File:Marvin-PCB.jpg\|800px]]

			[[File:Marvin-PCB-Back.jpg\|800px]]

Ⅹ: LoRa

2018-01-07T06:05:32Z

LoRa

New page

Some kind of LoRa device http://www.rdmmakerspace.nl/Marvin/

Source code here: https://github.com/iotacademy/marvin

The device is a bare PCB with a USB on one end. Plugging this in to a computer shows up as a Arduino Leonardo and can be reprogrammed as such from the Arduino IDE. There is also a micro usb connection presumably connected to the lora module in some way.

[[File:Marvin-PCB.jpg|600px]]